Inkqubo ye-uhlobo hook hook shot imbabala umatshiningokubanzi inembonakalo enkulu, kwaye inkqubo yofakelo inzima ngakumbi kunaleyo yezixhobo ezincinci. Ukufakwa ngokuchanekileyo kunye noomatshini wovavanyo sisitshixo ekuqinisekiseni ukusebenza kwesiqhelo kwezixhobo kamva. Kwimeko yokusebenza kokuqala okungenazakhono, abasebenzisi bayacelwa ukuba balandele ngokungqongqo imiyalelo yabasebenzi abafanelekileyo okanye babhekise kwimiyalelo. Ukusebenza okungagunyaziswanga kunokubangela umonakalo ongenakulungiseka kwifayile ye-hook shot umatshini kwakho imbabala. Inkqubo ye-shot blasting machine manufacturer has sorted out the precautions for installation and test machine to share with you. I hope it will be helpful to users who use the device for the first time.
1. Installation. Inkqubo ye-uhlobo hook hook shot imbabala umatshini is installed and debugged in the production plant and disassembled into several parts before being transported to the user site for installation. Although there is no pit, the foundation must be firm, the anchor bolt holes must be standardized, and the chamber body must be adjusted. After the second irrigation, the anchor bolt nuts can be tightened after solidification. After the chamber body is fixed, the various parts can be installed. Inkqubo ye-precautions for the installation and debugging of the relevant components are introduced below.
1. Shot isixhobo ukuqhumisa:
Inkqubo ye-shot blasting device has been installed on the chamber body before leaving the factory. Please pay attention to the problems to be debugged before use. Check whether the fixed positions of the blade, the pill wheel, the directional sleeve, and the guard plate are accurate and firm, and check whether the direction of rotation is correct after power on. Then adjust the position of the directional sleeve opening. Theoretically, the angle between the front edge of the directional opening and the front edge of the blade throwing position is about 900. After fixing the position of the directional sleeve, the position of the projectile belt can be detected by hanging Place a steel plate or wooden board on the position of the workpiece facing the exit of the shot blasting machine, start the shot blasting machine, put a small amount (2-5kg) of projectiles into the blasting tube, and then stop, check whether the hit position on the steel plate is suitable for the needs, such as Close the window of the bias-adjustable directional sleeve downwards, and vice versa, until it fits, and note the position of the directional sleeve opening as a basis for future replacement of the directional sleeve.
2.Ukuphakamisa isantya kunye nokujija ukuhambisa:
Kuqala yenza uvavanyo olungenamthwalo ukukhangela ukuba iemele zokumisa nokuphakama zihamba ngendlela elungileyo, emva koko qinisa ibhanti lokuphakamisa ukuphakama ukuya kwinqanaba eliphakathi lokuxhathisa ukunqanda ukuphambuka, emva koko wenze uvavanyo lomthwalo ukukhangela ukusebenza kunye nokuhambisa amandla, nokuba kukho nasiphi na isandi sokungcangcazela nokungcangcazela, jonga kwaye ususe imiqobo.
3. Isahluli sepilisi-isanti:
Kuqala jonga ukuba ukuhamba kwenkunzi yegusha kuyabhetyebhetye, emva koko ujonge indawo efanelekileyo yeplate yokwahlula, emva koko xa ukuphakamisa umthwalo kulayishiwe kwaye kulungisiwe, kukho ukuqhubekeka okuqhubekayo kokudutyulwa kwesinyithi, kwaye ujonge ukuba ingaba izithonga zentsimbi ziyaphuma kwaye ziyawa xa ikhonkco likhululwa